How to Clean the Gravity Reactor™ Water Hookah System

Regular cleaning helps keep your Gravity Reactor™ working smoothly and looking its best. This guide covers everything you need to maintain your system between sessions and over the long term.

For legal tobacco use only. This guide is intended for adult users in compliance with all applicable local laws.

---

1. What to Clean

Your Gravity Reactor™ system includes several components that require regular attention:

• Twin Glass Hydro-Gravity Reaction Chambers — the primary water chambers
• 14mm Mouthpiece — direct contact point; clean after every session
• 5 ft Hose — carries airflow; flush regularly
• Interchangeable Tube Sets — clean between uses to prevent buildup
• ABS Frame — wipe down the exterior to maintain appearance

---

2. How Often to Clean It

• After every session: Empty and rinse the glass chambers and mouthpiece.
• Weekly (or every 3–5 sessions): Full cleaning of chambers, hose, and tubes.
• Monthly: Deep clean all components; inspect for residue or wear.

---

3. Cleaning the Glass Chambers

1. Carefully detach both glass chambers from the ABS frame.
2. Empty any remaining water.
3. Rinse with warm water to loosen residue.
4. Add a small amount of isopropyl alcohol (91%+) or a dedicated hookah cleaning solution.
5. Cover openings and gently shake to coat the interior.
6. Rinse thoroughly with warm water until no cleaning solution remains.
7. Allow to air dry completely before reassembling or storing.

⚠ Handle glass carefully. Do not drop glass components. Glass chambers are precision-made and fragile. Damage from dropping or mishandling is not covered under warranty.

---

4. Cleaning the Hose and Tubes

1. Detach the hose and tube sets from the system.
2. Run warm water through the hose to flush out residue.
3. For deeper cleaning, use a flexible brush or pipe cleaner designed for hookah hoses.
4. Rinse the interchangeable tube sets under warm running water.
5. Shake out excess water and hang or lay flat to dry completely before reattaching.

Do not use harsh chemicals on hose or tube components. Mild soap or warm water is sufficient for routine cleaning.

---

5. Cleaning the ABS Frame

1. Wipe down the exterior of the ABS frame with a damp, lint-free cloth.
2. For stubborn spots, use a small amount of mild soap on the cloth — do not apply directly to the frame.
3. Dry immediately with a clean cloth.

⚠ Do not use harsh chemicals or abrasive cleaners on printed components. This includes acetone, bleach, or solvent-based cleaners, which can damage the finish and printed graphics.

Do not use excessive heat on printed parts — avoid hair dryers, heat guns, or placing near direct heat sources.

---

6. What to Avoid

• ❌ Dropping or striking glass chambers
• ❌ Harsh chemicals (bleach, acetone, solvents) on any component
• ❌ Excessive heat on ABS or printed parts
• ❌ Dishwasher cleaning — hand wash only
• ❌ Storing components while still wet or damp
• ❌ Using abrasive scrubbers on glass or frame surfaces

---

7. Storage Tips

• Let all parts dry completely before storage to prevent mold or odor buildup.
• Store glass chambers upright or in a padded case to prevent contact damage.
• Keep the system in a cool, dry location away from direct sunlight.
• Coil the hose loosely — do not kink or tightly wrap it.
• Reassemble loosely or store disassembled to allow airflow.

---

8. Final Care Notes

Proper cleaning and handling extend the life of your Gravity Reactor™ and maintain consistent performance session after session. Please note:

• The warranty does not cover damage resulting from improper cleaning, mishandling, or use of unauthorized cleaning agents.
• Always inspect components for cracks or wear before each session.
• If a component is damaged, discontinue use and contact us before your next session.

Questions about care or replacement parts? Contact our support team — we're here to help.

---

Helpful Links

• Shop the Gravity Reactor™ 360 Rotating Water Hookah System
• Read the Setup Guide
• View Warranty and Returns